Product Review: Atlas Pasta Drive Motor

Pasta Drive

Four Stars Rating: 4 stars (out of 5)

After several years as a slave of my hand-cranked

pasta machine (and sufferer of sore shoulders), I decided to get a pasta machine motor. A Christmas gift certificate helped make the purchase a much easier decision, but I felt that with all the claying I do, it would be worth the investment regardless of the cost.

I researched prices and found that Polymer Clay Express had the most reasonable deal ($80, as opposed to around $100 on other sites), so I placed my order for my Pasta Drive along with a nifty little accessory–a foot pedal ($18) similar to a sewing machine pedal. I’d be able to turn the machine on and off without using my hands–a nice feature when you’re working with a large or long piece of clay.

I receved the motor in good order. However, I found out that the older Atlas machine that I have didn’t have the requisite holes drilled around the crank case to attach the motor! Fortunately, I had another machine that had the drilled plate, so I did a little switcheroo and had a machine ready to motorize.

The machine has a crank shaft similar to the end of the crank handle plus two little catch bolts that secure and hold the motor to the machine. Ten seconds of fiddling and fitting (well, ten minutes and ten seconds, if you add the time it took to find and replace the plate), and I had a motor ready to go. I plugged it into my foot pedal, set my rollers on a #1 setting and I was ready to go. I had some clay flattened to get through the rollers–I know that if you put in too much clay at a time, you can really stress the engine–and I pressed down on the pedal to get the motor running.

WOW! LOUD LOUD LOUD! The motor is extremely loud. Almost ear-plug loud. I put the slab of clay through the machine, and the machine got louder and a bit slower until the clay was through. I folded and put the clay through again and went through normal conditioning, lickety-split. It was really nice to condition the clay in this manner, but I have to say that the noise could and will get very irritating in a short amount of time. However, the good thing about a foot pedal is that you don’t have to have the machine constantly on. You can turn it off and on easily and have your hands free at all times.

I took my slab of clay through the various settings of the pasta machine and found the performance of the motor to be just fine. However, I began to smell a bit of burning, and I immediately stopped the machine.

The nice thing about the polymer clay community is that there are a lot of people willing to help you with questions or problems. In order to find out what’s normal with this motor, I went to the Polymer Clay People Yahoo Group and asked people what was normal regarding noise, the burning smell and longevity of the motor. In no time at all, I had my answer:

- Yes, the noise level is normal. The slowing of the motor as it’s working is normal. Just don’t try to cram a bunch of clay through the machine; you should only put a sheet through that’s double or 3x the thickness of the setting at MOST.

- Yes, the burning smell is normal. Sometimes the motor burns off some of the oil used to lubricate the motor during manufacturing. The burning smell will subside.

- Yes, the motor lasts for a long time. People have quoted years of use with no end in sight.

These key pieces of information made me much more comfortable with my purchase. As we all know, when we’re unfamiliar with something, it’s always nice to hear that others have had the same experiences and the experiences are normal. That’s one of the reasons I’ve started this blog.

So, the Pasta Drive gets 4 stars out of 5. The noise kicked it down a notch. :-) I’m looking forward to less soreness in my shoulders and many more days of clay.

Digg!

About these ads

3 Comments

Filed under 4 Stars, Products, Tools

3 responses to “Product Review: Atlas Pasta Drive Motor

  1. Wow! Just learned about this site now.
    This review has helped a lot. Finally, after about 10 years of service my motor (PASTA FACILE) its starting to sound a bit tired (slow). I was considering the Makins machine with motor as an alternative, but not anymore. I’ll go with an Atlas motor from Polymer Clay Express (they have great service) and maybe an Atlas 180 machine to go with it since my Atlas 150 is about 12 years old and may not be compatible (as you mention in your Atlas Motor review). Thanks a lot.
    Norma I. Agron

  2. Rick

    I guess I’m a little late, but in regards to retrofitting a motor drive to an Atlas pasta machine, there is a motor conversion kit that may help:

    http://www.cutleryandmore.com/details.asp?SKU=12116

    • Betsy LT

      Thanks Rick!

      I was wondering about how to fit the motor onto an older model, so your post really saved the day. While I’d rather not have to pay for the conversion set, at least I now know it’s available and may give up hand-cranking someday soon.

      Thanks again.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s